BOARDS

Type of boards and accessories

Safety, impact absorbing HOCKEY SPORT CANADA TYPE boards are installed (NO steel glass stanchions; instead the glass is only secured to the boards) in compliance with all the latest trends in modern ice hockey.

Ice hockey boards

Delivered ice hockey boards meet all IIHF, ČSLH and SZLH regulations. Boards are installed directly on the flat cooling pad and can be removed at any time.

Technical parameters

Ice surface 56 ,00 x 26 ,00 m
Curve radius 8 , 5 m
Board height 1250 mm
Door width 1000 mm 6
Ice resurfacer gate 3000 mm 1
Total length of boards 150 bm

Technical description of individual components

Anchors for boards

Special anchor plates matching configuration of the structure, measured and installed along the perimeter of the boards

Surface finish: upper portion of anchors – Hot-dip zinc

Panels with lining

Solid, doubled, interchangeable (2 m standard units) panels with a steel frame made of jäckel steel members, lined with high strength and UV resistant white polyethylene panels, thickness: 10 mm (the material fully colored), all technical openings are blinded with plastic plugs, center line, blue lines and goal lines are marked at correct positions, fasteners are embedded to ensure a fully smooth surface finish.

Panels are adapted to be connected without any load bearing stanchions

The load bearing steel frames for the boards, compared to type 2000, are modified to include special, zinc coated compression elements and solid reinforcements to allow safety glass to be installed without the need for steel stanchions

Surface finish:

  • Hot-dip zinc – steel structure
  • zinc coating – fasteners

Gate for ice resurfacer and doors for players

These include piano-type hinges, an easy to control closing mechanism and the gate is equipped with rolling wheels to make handling easier.

Grab rails

Upper edge of the boards, high strength and UV resistant red (blue) polyethylene, rounded R10 edges, fasteners are embedded to ensure a fully smooth surface finish.

Surface finish: zinc coated (fasteners).

Toe boards

High strength and UV resistant yellow polyethylene, dimensions: 2000 x 200 x 10 mm , upper edges rounded with an R 10 radius, fasteners are embedded to ensure a fully smooth surface finish.

A groove is routed into the boards in order to install the lower portion of the advertising cover sheet

Surface finish: zinc coated (fasteners).

Type of safety glass

Safety, impact absorbing HOCKEY SPORT CANADA TYPE boards are installed (NO steel glass stanchions; instead the glass is only secured to the boards) in compliance with all the latest trends in modern ice hockey .

Construction of safety glass

Delivered safety glass meets all IIHF, ČSLH and SZLH regulations. The glass is installed at the height specified by the boards and can be removed at any time .

The safety glass used with CANADA type boards is characteristic in that it does not require the use of any steel stanchions, compression moldings and rubber gasket materials.

Technical parameters

Glass height :
Behind goal crease 1600 mm
Straight lengths 800 mm
Benches No glass

Technical description of individual components

Safety glass – behind goal crease (short straight section)

Hardened FLOAT safety glass (15 mm thick, dimensions based on glass installation location), installed into boards and secured with compression elements; upper sections of glass are secured with transparent (polycarbonate) fasteners that prevent the vibration of individual safety glass panels in special rubber components.

Safety glass – long straight side + corners of the boards

Hardened FLOAT safety glass (15 mm thick, dimensions based on glass installation location), installed into boards and secured with compression elements; upper sections of glass are secured with transparent (polycarbonate) fasteners that prevent the vibration of individual safety glass panels in special rubber components.

Advertising cover

Delivery of transparent polycarbonate cover for the boards to avoid on-going repairs to advertising signs

Technical parameters

Length of coverage 150 m
Height of coverage Approx. 1050 mm

Technical description of individual components
Polycarbonate: 3 mm thick

The upper portion of the cover is secured using a compression molding made of white polyethylene, the lower portion is secured to the routed groove in the toe boards; fasteners are embedded to ensure a smooth surface of the cover .

Surface finish: zinc coated (fasteners).

Protective netting

Technical parameters

Netting dimensions 2 pieces – 36 x 4 m

Technical description of individual components
Protective netting

Machine stitched polyamide netting, black color, eyelet size of 40 x 40 mm, rope thickness: 2 – 3 mm, complete with carabiners and turn buckles

Partitions and glass for benches

Delivered and installed partitions and glass for benches meet all IIHF, ČSLH and SZLH regulations. Partitions are installed at the level of the cooled surface (with height matching the boards) and can be removed at any time. 
Glass is installed in specific partitions and can be removed at any time. The glass used with CANADA type benches is characteristic in that it does not require the use of any steel stanchions, compression moldings and rubber gasket materials.
Technical parameters

Length of partitions 2 x 12 m
Width of partitions 1,5 m
Height of partitions 1250 mm
Total length of partitions 30 straight meters
Glass height
Verticalsection 800 mm

Technical description of individual components
Anchors for boards
Special metal HILTI type anchors – load capacity based on delivered structural calculation Surface finish: zinc coated
Panels with lining
Solid, interchangeable (2 m standard units) panels with a steel frame made of jäckel steel members, lined with high strength and UV resistant white polyethylene panels, thickness: 8 mm, all technical openings are blinded with plastic plugs, fasteners are embedded to ensure a fully smooth surface finish.

Panels are adapted to be connected without any load bearing stanchions.

The load bearing steel frames for the boards, compared to type 2000, are modified to include special, zinc coated compression elements and solid reinforcements to allow safety glass to be installed without the need for steel stanchions.

Surface finish:
Hot-dip zinc – steel frame
Zinc coated – fasteners

Door for players


Surface finish: zinc coated.

Grab rails

Upper edge of the boards, high strength and UV resistant red (blue) polyethylene, rounded R10 edges, fasteners are embedded to ensure a fully smooth surface finish.

Surface finish: zinc coated (fasteners).

Safety glass

Hardened FLOAT safety glass (15 mm thick, dimensions based on glass installation location), installed into boards and secured with compression elements; upper sections of glass are secured with transparent (polycarbonate) fasteners that prevent the vibration of individual safety glass panels

Acrylic is used for non-standard dimensions or may be delivered in glass.

Partitions and glass for penalty boxes and space for score keepers

Delivered partitions and glass for penalty boxes and space for score keepers meet all IIHF , ČSLH and SZLH regulations. Partitions are installed at the level of the cooled surface (with height matching the boards) and can be removed at any time.

The glass used with CANADA type benches is characteristic in that it does not require the use of any steel stanchions, compression moldings and rubber gasket materials .

Technical parameters

Length of partitions 2×4 + 5,5m
Width of partitions 1,5 m
Height of partitions 1250 mm
Total length of partitions 19 straight meters
Glass height
Verticalsection: 800 mm

Raised flooring for benches, penalty boxes and score keepers

Delivery of raised flooring (podiums) to facilitate easy access for players and other skaters to the ice surface. Raised flooring is installed at a height of 200 mm above the ice surface and can be removed at any time.

Technical parameters

Flooring in bench area 36 m 2
Flooring in penalty box and score keeper area 21 m 2
Standard dimensions of individual flooring units: 1000 x 2000 x 200 mm

Technical description of individual components
Raised flooring
Structural frame made of jäckel steel members, with wooden walking surface on top made of special, wear resistant plastic, 20 mm thick

Surface finish:
Hot-dip zinc – steel frame
Zinc coated – fasteners

Benches for players

Delivery of benches for players, ensures long service life and comfortable seating for resting players, benches are installed on raised flooring (or on concrete) and can be removed at any time.

Length of benches for players: 2×10 m
Length of benches in penalty boxes and for score keepers: 3×3 m
Standard dimensions of bench sections: 3 m

Technical description of individual components
Benches for players
Robust frame made of jäckel steel members and a separate seating section made of red polyethylene (also available in blue)

Surface finish:
Hot-dip zinc – steel frame
Zinc coated – fasteners

Protective surface cover for player areas

Delivery of a special surface cover for player areas in order to ensure players can walk on their skates and not damage the raised flooring. This cover can be delivered in a range of colors (blue, gray, black or brown) and can be removed at any time.

Technical parameters

Dimensions per piece Approx. 400 x 400 – puzzle shape
Thickness of surface cover 10 mm
Size of rubber surface
Benches 36 m 2
Penalty boxes and score keeper area 21 m 2

Technical description of individual components
Surface cover
Individual, interchangeable panels, puzzle shaped (facilitates replacement of a single piece if damaged ), adhered to the flooring.  These panels are produced using a special rubber, PVC and plastic mixture resistant to skate blades and ensuring a long service life of the entire surface.

Ice hockey goals

Delivery of goals, nets and padding for ice hockey, IIHF approved type

Technical parameters

Goal dimensions: Following IIHF rules
Number of goals: 2

Technical description of individual components

Goals
Metal frame (dimensions following IIHF rules) in combination of white and black colors, delivery of flexible or solid mooring pins. 
Surface finish: special baked on powder coating

Goal padding, protective netting
Frame padding (doubled canvas sheathing with padding) – secured with Velcro, safety netting – polyethylene, 4 mm thick, eyelet size: 40 x 40 mm, netting skate protection – thick-walled canvas